listing for P
ppdof - Text to PostScript print filter
/usr/lbin/ppdof +Cfilename [-n login] [-h host] [...]
Use of the print flags is dependent on the features available on the print
device, and on the current status of those features. For example, when you
select a particular paper size, the appropriate paper must be correctly
loaded in the paper trays.
Options in /etc/printcap
The following options are set in the /etc/printcap file and can be
specified using the + switch. For example:
:if=/usr/lbin/ppdof +Bupper +Cln32.rpd:\
You can also specify command line options in the /etc/printcap file using
the + switch. For example:
:if=/usr/lbin/ppdof +Olandscape +Cln32.rpd:\
Here, the -Olandscape option is specified.
Specifies the default tray name to select for printing the banner page.
:of=/usr/lbin/ppdof +Bupper +Cln32.rpd:\
In this example, the banner page will be printed on whatever stock is
currently loaded into the upper tray on the selected print device.
Specifies the printer configuration file to use for the print job.
Specifies the unit of measurement to be inches or centimeters for lines
per inch (lpi), characters per inch (cpi), and page margin options. The
default value is inches.
Specifies the default tray name to select for printing the trailer
page. For example:
:if=/usr/lbin/ppdof +olower +Cln32.rpd:\
Command Line Options
Specify print filter options at the command line using the lpr command as
follows. Multiple -O options are supported.
Specifies the host name from which the job owner is submitting the
Specifies the login (account) name of the job owner.
Specifies the name of the output tray where the printed pages are
Specifies the page width in columns for portrait and landscape
printing. A page width of 0 instructs the filter to use 80 columns in
portrait orientation and 132 columns in landscape orientation.
Specifies the tray name from which print paper is selected. The printer
may select an alternate tray when the paper size provided in the tray
does not match the document requirements.
Specifies the number of sides to print on each sheet. You can specify
sides as follows:
· 1 or one - Print on one side of the sheet.
· 2 or two - Print on both sides of the sheet (duplex printing).
Specifies options related to page orientation, formatting, and features
Specifies the number of characters to print per inch.
Specifies only even numbered sheets are to be printed.
Specifies the printed output is parallel to the long side of the
Specifies the number of lines to print per page.
Specifies the number of lines to print per inch.
odd Specifies only odd numbered sheets are to be printed.
Specifies the range of pages to be printed, starting with page
number m and ending with page number n.
Specifies to print the list of options provided by the printer
configuration file which includes paper sizes, input and output
paper tray names. For example:
# lpr -Oprint /etc/motd
(Note that the file /etc/motd is specified to satisfy lpr command
line requirements, the file itself is not printed.)
Specifies the printed output is parallel to the short side of the
[Tru64 UNIX] Continues text lines that exceed the right hand
[Tru64 UNIX] Truncates text lines that exceed the right hand
These options specify the various page margins in inches. The page
margin sizes in inches as follows:
· tm= - Top margin in inches. For example -Otm=2
· bm= - Bottom margin in inches. For example -Obm=1.5
· lm= - Left margin in inches. For example -Olm=1
· rm= - Right margin in inches. For example -Orm=3
· pm= - Page margin. Using this option sets tm, bm, lm and rm to
the same value. For example -Opm=1.25
When configuring the /etc/printcap entry, different margins for
landscape and portrait orientation can be specified by adding the
suffixes _l and _p respectively. For example:
:if=/usr/lbin/ppdof +Olm_p=0.5 +Olm_l=0.25 +Cln32.rpd:\
The ppdof filter translates ASCII to PostScript and handles the device
dependencies of a PostScript printer.
It is recommended that the ppdof filter be specified for both the :of and
the :if fields in the /etc/printcap file. For a description of these
fields, see the printcap(4) reference page.
The commands generated by the ppdof filter to handle device dependencies
might be incompatible with some PostScript documents. When a PostScript
file does not print correctly use the following command to prevent file
# lpr -x file.ps
The filter will not setup device dependencies or provide ASCII to
PostScript translation for documents containing printer control characters.
Any value other than zero (0) indicates that an error has occurred.
Use the lf error log field in the /etc/printcap to specify the name of the
error log file.
Commands: cancel(1), lpr(1), pr(1)
listing for P