Index Index for
Section 7
Index Alphabetical
listing for L
Bottom of page Bottom of
page

lat_manual_setup(7)

NAME

lat_manual_setup - Describes how to manually set up the Local Area Transport (LAT)

DESCRIPTION

To run LAT on your system, you must configure LAT in your system's kernel (see the Network Administration manual). Optionally, you can customize your LAT setup. The customization section of the Network Administration manual includes information on general customization, setting up printers, host-initiated connections, the LAT/Telnet gateway, and creating your own service. For more information on customizing LAT, see the Network Administration manual.

Setting Up LAT

To set up LAT on your system manually, you must first configure your kernel for LAT (see the Network Administration manual). Then log in as superuser and perform the following steps: 1. Create the LAT device special files. LAT supports SVR4-style and BSD-style devices. You should use SVR4- style devices. See the Network Administration manual for more information. Note You should use the latsetup utility to create SVR4-style devices to ensure that duplicate minor numbers are not used. You can use the mknod command to create character devices with a major number of 5. If you create SVR4 devices manually, you should observe the following rules: · Start the SVR4 device numbers at /dev/lat/620. This avoids overlapping minor numbers from the BSD tty name space. · Make the minor number of the SVR4 device the same as the name. For example, device /dev/lat/833 should have minor number 833. The following command would create the SVR4-style LAT device /dev/lat/833: # /usr/sbin/mknod /dev/lat/833 c 5 833 Once you have created the SVR4-style device, check the permissions of the device to make sure they are what you desire. You can create BSD-style devices by running the /dev/MAKEDEV script with the LAT option. The syntax for the MAKEDEV command with the LAT option is as follows: MAKEDEV latN The N variable can be 0 to 38. The /dev/MAKEDEV script creates one BSD-style LAT device special file for each LAT terminal device. When you run the MAKEDEV script, it creates 16 BSD-style LAT device special files, and creates the LAT control device (/dev/streams/lat), if it has not already been created. The MAKEDEV script requires 16 contiguous LAT device special files to be available. (Specifying lat38 requires only 12 contiguous LAT device special files to be available.) For example, the following commands create a total of 32 BSD-style LAT device special files: # cd /dev # MAKEDEV lat0 # MAKEDEV lat1 Record the device special file information displayed by the MAKEDEV script. The special file names vary depending on the number of terminal devices already configured. The following is sample output from the MAKEDEV command: MAKEDEV: special file(s) for lat1: tty16 tty17 tty18 tty19 tty1a tty1b tty1c tty1d tty1e tty1f tty1g tty1h tty1i tty1j tty1k tty1l 2. Edit the /etc/inittab file to include entries for the LAT device special files you created. For example: lat620:34:respawn:/usr/sbin/getty /dev/lat/620 console vt100 lat621:34:respawn:/usr/sbin/getty lat/621 console vt100 lat630:34:respawn:/usr/sbin/lattelnet lat/630 lattelnet The second field (34) specifies the run levels at which the LAT devices are spawned; in this example, the getty process is spawned at either run level 3 or 4. The first entry uses an absolute pathname for the device (/dev/lat/620). The second uses a relative pathname (lat/621). The previous example shows how to add entries to the /etc/inittab file for SVR4 LAT devices. The following example shows entries for BSD LAT devices: lat16:34:respawn:/usr/sbin/getty tty16 console vt100 lat17:34:respawn:/usr/sbin/getty tty17 console vt100 lat18:34:respawn:/usr/sbin/lattelnet tty18 lattelnet18 For more information, see the inittab(4) and getty(8) reference pages. The Network Administration manual provides additional information on SVR4 and BSD devices. 3. Use the following command to spawn the processes for the LAT device special files that you added to the /etc/inittab file: # /sbin/init q 4. Create the STREAMS special file required by LAT by issuing the following command: # /usr/sbin/strsetup -i 5. Enable LAT automatic startup and shutdown by using the following command: # /usr/sbin/rcmgr set LAT_SETUP 1 When LAT automatic startup and shutdown is enabled, the /sbin/init.d/lat file automatically starts LAT upon reaching run level 3 and automatically stops LAT when exiting run level 3. 6. Start LAT by issuing the following command: # /usr/sbin/latcp -s

RELATED INFORMATION

Commands: llogin(1), netstat(1), getty(8), init(8), latcp(8), latsetup(8), MAKEDEV(8), mknod(8), rcmgr(8), strsetup(8). Files: inittab(4). Introduction: lat_intro(7). Network Administration , System Administration

Index Index for
Section 7
Index Alphabetical
listing for L
Top of page Top of
page